Tammy and I
Sincerely Appreciate Your Patronage
Colt Revolver
Manufacturer of
Trigger Shims Brand
American Made Gun Shims
Gun Smith Supplies
Since 2008

God Bless the U.S.A.
God Bless America
and Samuel Colt!
COLT REVOLVERS
Colt Revolver Spring Kits are on our Wolff Gunsprings PageTriggerShims Brand Shims for Colt Revolvers
Shims for Trigger, Hammer, Cylinder Endshake and Crane
All Made from USA 300 Series Stainless Steel in .002" - .009" Stock
Colt Revolver Trigger / Hammer Shims
Our Colt Hammer or Trigger Shim Pak Assortments BELOW are as follows;
2 Pak comes in .002"
4 Pak comes with 2 each .002" and .003"
6 Pak comes with 2 each .002", .003" and .004"
8 Pak comes with 2 each .002", .003", .004" and .005"
12 Pak comes with 4 each .002", .003", .004"
20 Pak comes with 4 each .002", .003". .004", .005" and .006"
24 Pak comes with 6 each .002", .003", .004" and .005"
30 Pak Gunsmith Special Assortment comes with 6 each .002", .003", .004", .005" and .006"
Choose ANY Hammer or Trigger Pak and Specify Your Requested Thickness in Comment Box
Available in Stainless Steel ~ .002" - .009" Thickness
Colt M1917 / Colt New Service Revolvers
Colt New Service Revolver
Trigger (.140" X .244")
Hammer (.208" X .419")

Colt E/I Frame Revolvers
These include the Python, Official Police, Officer's Model Revolvers,
First Generation Troopers and the Model 357
Trigger (.120" X .190")
Hammer ( 198" X .243")


Colt D Frame Revolvers

D Frame Diamondback .22 Revolver
May Fit Other D Frames including ~
Detective Special, Police Positive Special
Trigger (.126" X .207")
Hammer ( 126" X .221")
Diamondback Revolvers built from 1966 to 1991
in Calibers .22 LR and .38 Special
These shims are made to fit revolvers with
nominal 1/8" Hammer and Trigger pins
Pistolsmith Tony contacted me about a new in the box, 1980 or 81 Colt Diamondback .22 Revolver. He noticed that the hammer and trigger had quit a bit of side to side play. In single action mode, it was no problem, but in double action the looseness of the two parts in the frame and on their respective pins allows them to shift position enough that the hammer would cock off to the left and impact the edge of the hammer channel in the frame

Fail To Fire ~ FTF
Tony said he was getting a lot of FTF in Doule Action, so he contacted me and asked if I could help. Tony disassembled the revolver and took pictures and accurate measurements, drew diagrams and prints, and from those I produced these shims for Tony's revolver.
While the shims did not fully cure the FTF problem, (he believes a new mainspring will be the final cure for that) they did remedy the Hammer Rub issue and helped immensley.
Thanks to Pistol-smith Tony for his Expertise on this Project!!
Colt New Frontier Single Action .22
Trigger and Hammer Shims
Trigger Shim
Nominal O.D. of .243" X I.D. of .126"
Same Shim as S&W Combat Magnum-X
Hammer Shim
Nominal O.D. .310" X .189"
This Shim Fits the Colt New Frontier Hammer,
The Uberti Colt Dragoon, and the High Standard Double 9 Revolver
Colt Revolver Cylinder / Crane Shims
Our Colt Hammer and Trigger Shim Pak Assortments BELOW are as follows;
2 Pak comes in .002"
4 Pak comes with 2 each .002" and .003"
6 Pak comes with 2 each .002", .003" and .004"
8 Pak comes with 2 each .002", .003", .004" and .005"
12 Pak comes with 4 each .002", .003", .004"
20 Pak comes with 4 each .002", .003". .004", .005" and .006"
24 Pak comes with 6 each .002", .003", .004" and .005"
30 Pak Gunsmith Special Assortment comes with 6 each .002", .003", .004", .005" and .006"
Choose ANY Pak and Specify Your Requested Thickness in Comment Box
Available in Stainless Steel ~ .002" - .009" Thickness
Colt Agent (early) Revolver Cylinder Endshake Shims

Our Shims will fit the Colt Agent before 1966
also fits - Ruger SP101
Nominal O.D. of .337" X I.D. of .221"
Price includes Free Shipping
Colt Python Revolver Cylinder / Endshake Shims
Our Shims will fit the Colt Python
Made from USA Full Temper 300 Series Stainless Steel
Nominal O.D. of .357" X I.D. of .265"
Made to fit end of Crane inside Cylinder,
Check your size before ordering.
NOTE: This is not a Factory recommended method of repair for this model
Consualt a qualified gunsmith if you have questions
Colt Single Action Army Revolver Cylinder / Endshake Shims
Our Shims will fit the Colt SAA

Fits First and Second Generation Colt SAA and Authentic Reproductions only ~ Uberti SAA / Hawes
Also fits Third Generation with Removable Bushing.
Nominal O.D. of .424" X I.D. of .357"

Colt Police Positive Revolver Cylinder / Endshake Shims
Our Shims will fit the Colt Police Positive D Frame Revolver
May Also Fit Other D Frames Including;
Agent, Cobra, Diamondback, Others ~ Check Your Sizes Before Ordering

Nominal O.D. of .401" X I.D. of .337"
Colt Official Police Revolver Cylinder / Endshake Shims
Colt Officier's Model Revolver

Colt Army Special / Official Police and Colt Officer's Model Revolver
Fits many "E" Frame Revolvers
Known to fit Colt New Army and Navy
and Colt Army Special
Pythons up to the early 1970's
1969 and prior (pre-MK III) Troopers
Early I-Frame with 1-Piece Extractor Rod, including models 3-5-7
All Trooper .38/.357 and Early Python, Detective Special and Viper
Also Fits ~ Enfield N0. 2 Mark 1 Revolver
Check your shaft size to verify ~ Fits .355" to .360" Crane
Nominal O.D. of .458" X I.D. of .362"
Stock # Colt OP
Colt New Frontier Single Action .22
Cylinder Shims
Also Fits Heritage Rough Rider .22

Nominal O.D. of .419" X I.D. of .221"
Many Colt SA .22 and Clones with 7/32" Base Pin
Installs on front of cylinder - Held by Base Pin
Stock # Colt N.F. /CS
An Excellent Resource for Colt Revolvers is here http://www.coltfever.com/Home_Page.php
We Cheerfully accept Cash, Money Order, and Credit Cards through our Secure PayPal Check-Out
All Website Orders are Shipped the Next Business Day
I will Ship Shims to USA, Canada and International
Gun Parts Shipped to USA Only

"American Made Gun Shims" - GunShims.com - TriggerShims.com
and
TriggerShims is a Trademark
of
Shively Sales
Michigan Center, Michigan
Copyright 2008 ~ 2020
BY PURCHASING SHIVELY SALES PRODUCTS
YOU ASSUME ALL RESPONSIBILITY FOR THEIR SAFE INSTALLATION AND USAGE.
YOU RETAIN ANY AND ALL RESPONSIBILITY FOR YOUR OWN ACTIONS. Be Safe!!
If you have any questions or safety concerns, see a qualified Gunsmith.
Website Problems contact Webmaster@TriggerShims.com